MAGNA SOFT Campus Placement Drive on 10/07/2018. Zeal Technologies Campus Placement Drive on 11/07/2018. Data Point Pvt. Ltd. Campus Placement Drive on 18/07/2018. Admissions under B-category ( Management Quota) B.Tech First year available. Last date - 23rd July 2018. Lateral entry for 2nd year Admissions. Contact : 99853 59601, 879010105
Hybrid Power generating system Project done by students (with combination of WIND(15 W) and SOLAR(150 W) ). From Wind & Solar system we are getting 15 W &150 W. Total capacity of the Hybrid System is 165 W. The power generated from this is being used in Examination branch Lighting loads the college.
Some of the inhouse projects done by students of Electrical and Electronics Engineering are
Automatic water sprinkler system
Remote control systems for on and off of fans and lights
power generation while running and walking systems.
Remote control of loads using mobile GSM technology.
Wastewater is anything from water that flows down the sink or toilet to runoff from snow and rain that enters storm drainage systems. Wastewater treatment processes remove a variety of contaminants from water to make it usable again.
The benefits of such treatment depend on the nature of the contaminants in the water and the end use of the water treated.
Water is a renewable resource because it gets purified through evaporation and rain; however, only about 3 percent of the earth’s water is potable. Read More
The Vamsadhara Project
Vamsadhara is the main river of North Eastern Andhra. The North Eastern Andhra region consists of three North Eastern Coastal districts in Andhra Pradesh state in India. Vamsadhara project is designed to meet the irrigation needs of North Eastern Coastal Andhra
The Vamsadhara project has two canals viz., the left main canal (LMC), irrigating about 148,000 acres (600 km2), and the right main canal (RMC) covering an ayacut of 62,280 acres (252 km2). The left main canal was completed long back. The right main canal was delayed due to various reasons. Gotta Reservoir feeds the right main canal. About 166 villages in seven mandals.
L.N.Peta, Hiramandalam, Burja, Amadalavalasa, Gara, Sarubujjili and Srikakulam will be benefited.
The Lower Vamsadhara project envisages construction of 58m high & 1700m long dam across the vamsadhara river near Minajhola village (near 19°31′00″N 83°44′30″E ) in Rayagada district creating hydraulic head of nearly 62 meters. This project would be a multipurpose project serving power generation, irrigation and flood control.
A 30 km long gravity canal is planned to link the Vamsadhara and Nagavali Rivers. It will run from Hiramandalam reservoir to Narayanapuram barrage near Amudalavalasa and bring an additional 50,000 acres of ayacut under irrigation using 10 Tmcft of water from Vamsadhara basin.
PROJECT – MECHANICAL
1. Eco friendly ecar a major project designed and executed by 2016 pass out batch of Mechanical Engineering
Fabricated as a major project.
Seating capacity of two persons.
Maximum speed of 25 Kmph.
Runs on two 12V batteries.
Continuous run up to 9 Km when fully charged.
A new horizon in the field of sustainable energy.
A paradigm shift towards non-conventional energy sources for short distance transportation
2. Crucible furnace – a minor project designed and executed by 2016 passout batch of mechanical engineering
Used for melting metals for casting.
Reaches maximum temperatures upto 1400-1500 degree Celsius.
Coal and air fired with an air fuel ratio of 400:1.
Fitted with 1 hp centrifugal air compressor for quick heating.
Insulated with fiberglass wool for high thermal efficiency.
3. Articulated robotic arm- a minor project designed by 2015 passout batch of mechanical engineering
Made with planks of plywood
Operated by hydraulics using syringes as pistons.
Won the first prize at JNTUH conference on robotics and automation held at university auditorium.
4. Kinematic models of various mechanisms
Models of various kinematic schemes were prepared by mechanical engineering students out of interest as a extracurricular activity.
These models help in comprehending the technicalities of the kinematics of machinery and mechanism and their dynamics as well.